Normal:
Gold-N-Clear is a highly concentrated formula and should be diluted before adding to the pool. Add correct dosage to a pail filled with pool water (water in pail will turn a blue color) then apply entire mixture into pool around pool edge. Circulate water for several hours.

Initial Treatment: 1 oz. per 6,000 gallons. For very cloudy water, use 1 oz. per 3,000 gallons.
Maintenance Treatment: 1 oz. per 6,000 gallons every week for heaver swimmer load. For light swimmer load, apply 1 oz. per 6,000 gallons every 2 weeks.

Tips:
For best results, use Gold-N-Clear regularly, especially after each filter backwashing or cleaning, as well as after algaecide treatment to remove dead algae particles.
 

DIRECTIONS FOR USE:

FOR EXISTING CLOUDY WATER SWIMMING POOL
Backwash or clean filter following manufacturer’s instructions.
After backwashing, add ½ quart of Clarifier per 10,000 gallons of water, directly to skimmer.
Add additional doses as necessary to clear water, allowing 24 hours of continuous filtration between
additions.

FOR EXISTING CLOUDY WATER  HOT TUB OR SPA
Backwash filter, add 1 capful per 200 gallons in front of water inlet for maximum dispersion.
Repeat dose as needed to clarify water, allowing 24 hours of continuous filtration between doses.

MAINTENANCE DOSAGE  SWIMMING POOL
After backwashing filter, add 4 fl oz. of Clarifier per 10,000 gallons, directly to skimmer.
Repeat dose once-a-week.

MAINTENANCE DOSAGE  HOT TUB OR SPA
Backwash filter, add 1/2 capful per 400 gallons in front of water inlet for maximum dispersion.
Repeat dose once-a-week.

DIRECTIONS FOR USE:
Dilute Super Clarifier by adding it to a bucket of pool water.
Pour this solution around the inside perimeter of pool.
Operate pump and filter for 24 hours.
Usual dosage is 1 oz. per 5000 gallons of water, however, under extreme conditions of turbidity
(algae growth, newly filled pools, warm weather, start up etc.) dose 1 oz. per 2500
 

Standard Dosage:
Use 1 fl. oz. per 6000 gallons of pool water, no premixing required.

Cloudy Water Dosage:
For especially dirty or cloudy water, double or triple the standard dosage.

Weekly Maintenance:
To keep pool water clear and clean, use once a week at the standard dosage.
For heavy use or commercial pools, product can be used twice weekly at double or triple the dosage.
1. Make sure filter is clean and all equipment is working properly.
2. Squirt the calculated amount into the water with filter system running.
Run continuously for at at least six hours after application.
 

2 liters treats 33,800 gallons

Directions:
1. Add two ounces per/thousand gallons (60ml per 3750L), one capful treats 2000 gallons (7500L).
2. Broadcast Pool First Aid over the surface of the pool. Can be used every two days until the pool is crystal clear. Apply directly to water line to quickly remove any existing water line build-up.

Note:
Do not use within 2 hours before or after shocking.
If water temperature is below 70 degrees F, Pool First Aid will work more slowly,
so allow more time for results.

Recommended Dosage:
1oz. per 4000Gal (for trouble pools), 1oz. per 6000Gal weekly  

Spray Clear & Perfect at recommended dosage rate per gallons of pool water over entire pool water surface, concentrating on deep water areas. Spray Clear & Perfect onto water surface until you reach suggested amounts of ounces per gallons of water for your pool. See bottle for amount. Do not overdose pool. Clear & perfect may be oxidized by high levels of sanitizer. Do not use Clear & Perfect within 24 hours of using MetalFree or any other metal or stain remover.

General:
Poly-Brite will perform best if the pH of the water is at 7.4 or above. If below 7.4, the pH on most pools can be raised by the addition of pH Increaser ( sodium carbonate / soda ash ). The use of Poly-Brite will slightly lower the pH of the water, so any increase in pH made is usually counteracted by the Poly-Brite itself. As the Poly-Brite dissolve, they react with the pool water to form a dual-action floc on the filter media ( whether sand, D.E, or cartridge).  The use of Poly-Brite will dramatically increase the effectiveness of a properly operating filter, and may shorten the filter run the first few times it is used as organics and other, usually, un-filterable, compounds are captured. After the first few treatments, the water becomes cleaner and filter runs will return to normal. NOTE: The filtration system must be correctly sized and in proper operating condition for Poly-Brite to perform. This product will not correct a damaged or incorrectly sized or operated filter.

Procedure by Filter Type ( Remember - raise pH to 7.4 if necessary )

Sand Filter
  Backwash Filter    Return to filter mode and run for 2 hours to settle the sand bed. Flw rate should not exceed 15 gpm / sq.ft. filter area.    Apply correct dosage of Poly-Brite Tabs to skimmer, gutter, or surge pit. Make sure skimmer is clean and contains no other chemicals.    Dosage: Apply at the rate of (1) one ounce per square foot of filter area. Each Poly-Brite Tab weights 1/2 ounce. To determine the correct treatment dosage, multiply  the square footage of the filter by 2. Example: A 30,000 gallon pool with a 4.9 sq. ft. sand filter will use 10 Poly-Brite Tabs per treatment ( 4.9 X 2 = 9.8 ) round to 10. Follow product label instructions.

D.E. Filter
  Backwash and clean filter elements.   Precoat with required amount of diatomaceous earth (D.E.). Flow rate should not exceed 1.5 gpm / sq.ft. of filter area.   Apply correct dosage of Poly-Brite Tabs to skimmer, gutter, or surge pit. Make sure skimmer is clean and contains no other chemicals.    Dosage: Apply at the rate of 0.08 ounces per square foot of filter area. Each Poly-Brite Tab weights 1/2 ounce. To determine the correct treatment dosage, multiply  the square footage of the filter by 6.25. Example: A 30,000 gallon pool with a 60 sq. ft. D.E. filter will use 10 Poly-Brite Tabs per treatment ( 60 ÷ 6.25 = 9.6 ) round to 10. Follow product label instructions.

Cartridge Filter
  Clean filter elements. Replace if necessary.    Return to filter mode. Flow rate should not exceed 0.375 gpm / sq.ft. of filter area.   Apply correct dosage of Poly-Brite Tabs to skimmer, gutter, or surge pit. Make sure skimmer is clean and contains no other chemicals.    Dosage: Apply at the rate of 0.01 ounces per square foot of filter area. Each Poly-Brite Tab weights 1/2 ounce. To determine the correct treatment dosage, multiply  the square footage of the filter by 50. Example: A 30,000 gallon pool with a 450 sq. ft. D.E. filter will use 9 Poly-Brite Tabs per treatment ( 450 ÷ 50 = 9 ). Follow product label instructions.

Frequency of Application:
Poly-Brite should be added following each filter cleaning. Once the water is crystal clear and filter runs have returned to normal, application of Poly-Brite Tabs will be dependant on bather loads and water clarity.